Bently Nevada 31000-26-05-00-100-03-02 Proximity Probe Housing Assembly for 3300 Series

Bently Nevada 31000-26-05-00-100-03-02: Industrial Data Link for 3300 Series Vibration Monitoring Networks

The Bently Nevada 31000-26-05-00-100-03-02 Proximity Probe Housing Assembly is a precision-engineered component at the heart of rotating machinery protection and industrial connectivity. Designed for the Bently Nevada 3300 Series monitoring platform, this probe housing assembly serves as the critical physical interface between field-level vibration sensors and the broader plant automation network — enabling real-time signal acquisition, continuous data transmission, and seamless integration with SCADA, DCS, and HMI systems across smart factory environments.

In modern industrial facilities, the integrity of the data chain begins at the sensor level. The 31000-26-05-00-100-03-02 ensures that eddy-current proximity probe signals are captured with mechanical precision and routed reliably into the Bently Nevada 3300 XL 8mm Proximity Transducer System signal conditioning chain. From here, conditioned vibration data flows through the Bently Nevada 3500 Series Machinery Protection System rack — where modules such as the 3500/42M Proximitor/Seismic Monitor and 3500/22M Transient Data Interface process, timestamp, and transmit shaft displacement, eccentricity, and radial vibration values upstream to plant-level systems.

Compatibility & Integration Notes

Connected Automation Data Flow

The 31000-26-05-00-100-03-02 sits at the origin point of a sophisticated industrial data flow architecture. Once installed on the bearing housing or machine casing, the proximity probe — guided and protected by this housing assembly — generates a continuous analog voltage signal proportional to the gap between the probe tip and the rotating shaft. This raw signal is fed into the Bently Nevada 3300 XL Proximitor Sensor, which conditions and linearizes the output before passing it to the 3500/42M Proximitor/Seismic Monitor card seated in the 3500 Series rack.

Within the 3500 rack, the monitor card applies alarm setpoints, processes dynamic waveform data, and communicates machine health status to the plant DCS or PLC layer — commonly a GE Automation & Controls Mark VIe Controller or a Rockwell Automation ControlLogix PLC — via hardwired relay outputs or digital communication modules. For facilities running Modbus TCP/IP or PROFIBUS DP networks, the 3500/92 Communication Gateway Module bridges the machinery protection system into the plant-wide fieldbus backbone, allowing SCADA operators to view live vibration trends, alarm states, and historical waveform data without leaving the control room.

At the SCADA and HMI layer, Bently Nevada System 1 Evolution software aggregates data from multiple 3500 racks across the plant, providing asset performance dashboards, trend analysis, and predictive maintenance alerts. For facilities using third-party SCADA platforms such as Wonderware InTouch, Ignition by Inductive Automation, or Siemens WinCC, the OPC-UA server embedded in System 1 provides a standardized data bridge — ensuring that vibration, phase, and gap data from the 31000-26-05-00-100-03-02 probe circuit reaches every level of the automation hierarchy in real time.

Remote I/O extensions and edge gateways — such as the Bently Nevada TDIXl Transient Data Interface or third-party Moxa industrial Ethernet switches — further extend the network reach of the 3300/3500 monitoring chain to remote compressor stations, offshore platforms, and multi-site power generation facilities, enabling centralized remote diagnostics and alarm management from a single NOC or operations center.

Solving Data Isolation in Industrial Sites

One of the most persistent challenges in rotating machinery environments is data isolation — where vibration monitoring systems operate as standalone islands, disconnected from the plant DCS, ERP, or predictive maintenance platforms. The Bently Nevada 31000-26-05-00-100-03-02, as part of the 3300/3500 ecosystem, directly addresses this problem by providing a mechanically reliable, signal-accurate foundation for a fully networked machinery protection architecture.

Protocol fragmentation is eliminated through the 3500 rack’s multi-protocol communication options: Modbus RTU for legacy serial networks, Modbus TCP/IP and PROFIBUS DP for modern fieldbus environments, and OPC-UA for IT/OT convergence initiatives. This means that whether your plant runs a legacy DCS or a modern IIoT-enabled SCADA platform, the vibration data originating from the 31000-26-05-00-100-03-02 probe circuit can be normalized and delivered to any upstream system without custom middleware or protocol converters.

Production line transparency is achieved through continuous, uninterrupted data streaming from the proximity probe to the SCADA dashboard — with configurable alarm thresholds, automated shutdown relays, and event-triggered data capture ensuring that no critical machine event goes undetected or unlogged. Remote diagnostics capabilities allow maintenance engineers to interrogate machine health, review waveform snapshots, and adjust alarm setpoints from any networked workstation — reducing unplanned downtime and eliminating the need for on-site manual inspection during routine monitoring cycles.

System scalability is built into the 3500 rack architecture: additional monitor cards can be added to expand coverage to more measurement points, and multiple racks can be networked together under a single System 1 server — making the 31000-26-05-00-100-03-02 a future-proof investment for growing industrial facilities.

Industrial Connectivity FAQ

Q1: What communication protocols does the Bently Nevada 3300/3500 system support when using the 31000-26-05-00-100-03-02 probe housing?
The 3300 Series probe housing feeds into the 3500 Series rack, which supports Modbus RTU, Modbus TCP/IP, PROFIBUS DP, and OPC-UA via the 3500/92 Communication Gateway Module and System 1 software. This enables integration with virtually any modern DCS, SCADA, or HMI platform.

Q2: How does this probe housing contribute to network stability and signal integrity in high-vibration environments?
The 31000-26-05-00-100-03-02 housing is precision-machined to maintain consistent probe-to-target gap geometry, minimizing signal noise and drift. Combined with the 3300 XL Proximitor’s built-in signal conditioning, the system delivers stable, low-noise analog outputs even in high-EMI industrial environments — ensuring reliable data transmission to upstream network nodes.

Q3: Can this component be integrated into an existing SCADA or HMI system without replacing the entire monitoring rack?
Yes. The 31000-26-05-00-100-03-02 is a field-replaceable housing assembly compatible with the existing 3300 Series probe and cable infrastructure. As long as the 3500 Series rack and communication gateway modules are in place, replacing or adding this housing does not require reconfiguration of the SCADA or HMI integration layer.

Q4: What warranty and pre-shipment testing does ZYPLC provide for the 31000-26-05-00-100-03-02?
Every unit supplied by ZYPLC is covered by a warranty terms confirmed during quotation and undergoes pre-shipment functional verification to confirm mechanical integrity and dimensional compliance with Bently Nevada 3300 Series specifications. Availability is confirmed via RFQ for shipment arranged after confirmation with full export documentation. Contact our team at plc.sales@zyplc.com or +86 19859288691 for availability and lead times.

© 2026 ZYPLC. All rights reserved. | Contact: +86 19859288691 | plc.sales@zyplc.com